Self-stick vinyl floor tile installation

Popular Collections American Personality 12 Vivero. See all Luxury Vinyl Tile. Close Luxury Vinyl Tile Menu. Engineered Tile.

Engineered Tile What is Engineered Tile? Popular Collections Alterna. See all engineered tile. Close Engineered Tile Menu. Vinyl Sheet. Vinyl Sheet What is Vinyl Sheet? See all Vinyl Sheet. Close Vinyl Sheet Menu. Vinyl Tile. Vinyl Tile What is Vinyl Tile? Browse by color Gray Beige White Brown.

Inspiration Design a Room. See all Vinyl Tile. Close Vinyl Tile Menu. Share Share. Download F Installation Guide for Contractors. Before You Buy. Know your installation options. Consider any installation challenges. Create an accurate budget. Decide whether to DIY or bring in a Professional. Hiring a Pro? Find the best one for the job. Read the installation instructions.

Prepare the room. Prepare the subfloor. If you misalign a tile, you'll probably have to pull it up and replace it. The tile will likely be damaged, but you might be able to find a place for it as a cut tile in a corner. Also, the paper backings on self-stick tile are slippery underfoot. Place a wastebasket at your side as you lay the tiles. Don't remove the tile backing until you're ready to set the tile.

Dispose of the backing immediately. You can expect to spend about 2 hours tiling an 8xfoot floor. Before you begin, repair and clean the floor. Prime the subfloor, if necessary, with the product recommended by the manufacturer. Most primed surfaces benefit from two applications; the first one thinned and the second full strength. Both coats will go on easily with a long-handle roller. Snap chalk lines from the midpoints of opposite walls to locate the center of the room. Square the lines with a triangle and dry-lay the tiles along each axis.

Move the layout until you have even tiles at the edges, then resnap the lines. Arrange the tiles loosely along the layout lines with the arrows grain facing in the same or opposite directions depending on the look you want. Starting at a corner of the tile and working slowly, peel away the paper backing. Don't pull fast; you might tear the backing, and a fresh edge is difficult to raise from the center of the tile.

Set the corner of the tile at the intersection of the lines and press it down. Then roll it with a small roller. Using the layout configuration of your choice, continue setting the tiles, making sure each one butts squarely against its neighbors on two sides.

Don't forget to maintain the arrows consistently. When laying vinyl on wood floors, we recommend an expansion joint of mm due to the movement of the sub-floor. Generally, wood and vinyl have opposite stretching behavior, i. If it is ensured that the surface is level, you should ensure that the old wooden floor and the new vinyl flooring are decoupled from each other.

A decoupling film between wood and vinyl is definitely necessary here. There are basically two methods for this decoupling:. You can use a commercially available 0. Impact sound insulation db-cover underlay mats made of latex , which is also recommended for wooden floors as a subsurface for reasons of acoustics.

Many manufacturers even strongly recommend the use of impact sound insulation. You should definitely follow this recommendation, also for reasons of later warranty. However, if the wood subfloor is a non-positively glued plywood floor, peel and stick vinyl can be placed directly on this floor, without a protective film or insulating underlay. Plywood is a common underlayment, with better structural strength and water resistance than particleboard. Plywood used as an underlayment for peel and stick vinyl flooring should have a sanded, smooth surface on the topside.

Avoid using materials with distinct raised grain patterns and voids, which can affect the finish adhesion of the self-adhesive vinyl. To prepare the right plywood for peel and stick PVC floor, follow the below steps to install the plywood:. Cleaning the subfloor before installing plywood underlayment. Debris left on the subfloor can cause problems with the underlayment down the road, such as the void which could allow noticeable movement, floor squeaks or cause fasteners to poke through.

The goal is to have a wooden subfloor consisting of two layers at least 1-inch thick. Arrange the plywood on the floor so the joints of this layer do not align with the subfloor joints below.

Secure the plywood to the subfloor at 6-inch intervals with 1-inch deck screws placed along the edges. Set all screw heads slightly below the surface.